Toxic Black Mold Health Issues - Dangers of Black Mold

13 Common Breeding Grounds for Toxic Black Mold and Mildew

Next Page - It's Doing That To My Health? / Back to Combating Mold

Toxic Black Mold Problem #1

Leaky air-conditioning duct joints, especially those running through a hot attic, create a moist environment for toxic black mold & mildew.

Solution: Seal all air conditioning duct joints with the special flexible mastic tape available at heating and cooling supply and do it yourself hardware stores.

Toxic Black Mold Problem #2

In warm environments, impermeable vinyl wall-coverings can trap moisture-laden air as it moves from the warm exterior to the cooler interior. Toxic Black Mold degrades the drywall and adhesive behind the vinyl wall-covering.

Rates are at Historic Lows - Refinance Today Loan Type: ---Select ---- Home Purchase Home Refinance Loan Amount: ---Select --- $100,000$150,000$200,000$250,000$300,000$350,000$400,000$450,000$500,000$550,000$600,000$650,000$700,000$750,000$800,000$850,000$900,000$950,000 Property State: -----Select--- AlabamaAlaskaArizonaArkansasCaliforniaColoradoConnecticutDelawareDistrict of ColumbiaFloridaGeorgiaHawaiiIdahoIllinoisIndianaIowaKansasKentuckyLouisianaMaineMarylandMassachusettsMichiganMinnesotaMississippiMissouriMontanaNebraskaNevadaNew HampshireNew JerseyNew MexicoNew YorkNorth CarolinaNorth DakotaOhioOklahomaOregonPennsylvaniaRhode IslandSouth CarolinaSouth DakotaTennesseeTexasUtahVermontVirginiaWashingtonWest VirginiaWisconsinWyoming

Solution: Use paint or apply wallcoverings with permeable paper backings that don't trap moisture on exterior walls.

Toxic Black Mold Problem #3

When washing machines in a room without a floor drain overflow or hose connections burst, water with no point of exit will soak into adjacent carpet, drywall and insulation.

Solution: Always provide a floor drain near the washing machine. Install an overflow pan directly under the machine or install a 1-in. lip at the doorway to contain overflows in main-level or second-story laundry rooms. (An overflow pan is available for about $125 plus shipping from AMI, 800-929-9269.)

Toxic Black Mold Problem #4

Water-resistant drywall used as a the backer quickly degrades once subjected to moisture.

Solution: Install cement backer board, which will remain structurally sound even if repeatedly subjected to moisture.

Toxic Black Mold Problem #5

Poorly ventilated bathrooms allow surface mold to grow.

Solution: Install a bathroom fan (or at least, open a window) to exhaust moisture. Remove surface mildew by scrubbing the area with a 1/2 percent bleach solution. When the area is dry, prime it with an alcohol-based, white pigmented shellac, such as Zinsser Bulls-eye, and use a paint containing mildewcide.

Toxic Black Mold Problem #6

Poorly constructed crawlspaces promote mildew growth. Bare earth floors transmit huge amounts of moisture.

Solution: There are many regional differences and solutions. Cover bare earth with 6-mil poly sheeting. Heat, cool and humidify the area the same as the rest of the house.

Toxic Black Mold Problem #7

Freshly cut firewood stored indoors emits huge amounts of moisture.

Solution: Store it outside.

Toxic Black Mold Problem #8

Humidifiers (especially reservoir-type central units and portable units) provide both a growth medium and a distribution system for mold and mildew.

Solution: Clean and treat the reservoir often with an antimicrobial solution, available at most hardware stores.

Toxic Black Mold Problem #9

The condensation pan directly under the coil of your central air conditioner can harbor mold.

Solution: Before each cooling season, clean the pan with a 1/2 percent bleach solution and make sure the continuous drain is working.

Toxic Black Mold Problem #10

Finished concrete basements that haven't been thoroughly waterproofed from the outside are problematic. When moisture migrates through the earth and non-waterproofed concrete walls, it can get trapped behind vapor barriers, carpet, layers of insulation and drywall.

Next Page / Back to Combating Mold